Commercial Roofing · Winchester, KY
As a Winchester commercial roofing contractor, we install TPO, EPDM, and metal roofs, repair leaks, and replace worn roofs across Clark County and nearby towns.
Your First Visit
Repair, Recover, Or Replace
Each roof area gets one of three paths after a Winchester commercial roofing contractor walks it, cuts cores, and checks the deck from below.
A moisture scan and core cuts decide the path. Building code limits recovers over wet roofs and over roofs that already carry two layers.
Our Services
Six kinds of roof work, from one leaking seam to a full plant roof replacement.
Leaks at seams, split pipe boots, loose flashing, and clogged drains get traced from the stain inside to the spot on the roof. We fix the source and say plainly when patching no longer makes sense.
Commercial roof repair in WinchesterWhite TPO sheets are welded with hot air, so the laps fuse into one surface across the deck. We install it mechanically attached or fully adhered, matched to your deck type and the wind exposure at the corners.
TPO roofing in WinchesterSynthetic rubber sheet stays flexible through central Kentucky cold snaps. We join new EPDM laps with primer and seam tape, roll every seam, and hand-flash each drain bowl and parapet wall, where rubber roofs leak first.
EPDM rubber roofing in WinchesterPonding on a flat deck usually traces back to missing slope. A replacement lets us lay tapered insulation, crickets, and larger drains from scratch, then pick the membrane that suits the building after core cuts settle tear-off or recover.
Flat roofing in WinchesterPlant roofs carry exhaust fans, heavy rooftop units, pipe racks, and weekly foot traffic. We match the membrane to what the fans discharge, raise low curbs, and replace a working plant roof one section at a time.
Industrial roofing in WinchesterStanding seam and R-panel roofs cover offices, shops, barns, and warehouses. We install new panels, replace backed-out screws and leaking end laps, and build retrofit framing that turns a ponding flat roof into a sloped one.
Commercial metal roofing in WinchesterHow It Works
Five decisions, made in order, so the roof you pay for matches what was found on the deck.
We walk every seam, curb, drain, scupper, parapet cap, and run of edge metal, then check the deck from inside. Soft spots get core cuts, so wet insulation shows up before anyone prices a new roof.
Each roof area lands in one group: repair, recover, or full tear-off. You see which area comes first and why, with the moisture readings and core results that point there.
Flat decks behind parapets take TPO or EPDM. Shops, barns, and equipment buildings with real slope take metal panels. Plants with grease or process vents get a membrane checked against what the fans discharge.
Insulation thickness, tapered layout, cover board, and curb heights get set before materials are ordered, because edge metal height and drain extensions follow from those choices.
Roof sections are torn off and dried in before the crew leaves each day. Crane space, dumpster spots, shields over air intakes, and quiet hours for production or services are agreed with you first.
Call and tell us where the stain is, what sits on the roof above it, and how to reach the hatch. That is enough to start tracing the leak.
Roof Warning Signs
Most roof problems give a signal somewhere you already walk. Here is what to look for, and where.
Water sheeting over the gutter edge in normal rain points to clogged downspouts or undersized gutters.
A coping cap or drip edge raised at a corner, where wind uplift on a roof is strongest.
Orange runs below a scupper or panel lap show water leaving the roof in the wrong place.
Rings that grow after each storm, often a few feet from the seam or curb leaking above.
Drips beside an HVAC unit usually trace to cracked sealant or low flashing at its curb.
Rust or dark patches on the steel deck where wet insulation sits above it.
Puddles still standing two days after rain, most often in low bays or behind rooftop units.
Laps lifting across several rolls at once, the pattern that points toward replacement.
Spongy insulation under the membrane means water has already soaked in somewhere.
Benefits
A roof installed over a checked deck, with slope and flashing built in, changes what the building needs from you each year.
The Main One
When the roof is replaced as one assembly, the leaks that kept moving from seam to seam stop at the source. Insulation, cover board, membrane, flashing, and edge metal go on together and are matched to each other.
A tear-off is the moment to bring insulation under the new membrane up to energy-code levels.
Tapered boards, crickets, and new drains are laid out from scratch, so low bays stop holding water.
Each repair, curb height, and drain location gets written down, so the next roof walk starts informed.
Service Area
We take commercial roofing jobs in Winchester and five towns nearby: Mount Sterling, Jeffersonville, Carlisle, Owingsville, and Camargo.
Outside these towns? Go ahead and call us or send us a message.
FAQ
Short answers to what owners ask before a roof walk. More are on our commercial roofing FAQ page.
All of them, from the deck up. On a low-slope building that means insulation boards for thermal value, a cover board that takes foot traffic and hail, a TPO, EPDM, or PVC membrane, flashing up parapets and around curbs, and edge metal or coping along the perimeter. Drains, scuppers, and gutters complete the system by carrying water off.
Warehouses, plants, distribution buildings, schools, churches, retail strips, offices, and steel farm buildings all do, and the roof shape points to the system. Flat decks behind parapets take single-ply membrane. Steeper shop and barn roofs take metal panels. Where a brick office front meets a steel warehouse bay, each roof gets its own system, joined with flashing at the wall.
Square footage, the system chosen, and what turns up under the old roof drive most of it. Building height sets crane needs, and every curb, drain, skylight, and foot of edge metal adds flashing work. Deck repair is the variable to watch: two roofs of the same size can price very differently when one hides a rusted deck.
The City of Winchester Building Inspections department, which covers the city and the rest of Clark County. A downtown storefront and a warehouse on a county road go to the same office. Bring a scope listing roof area, system, insulation, deck repair, and new curbs or drains. Jobs with structural changes or retrofit framing are the likeliest to need drawings.
A commercial roof inspection in Winchester, KY starts with a full walk: seams, flashing, curbs, drains, scuppers, parapet caps, and edge metal, plus the deck from inside. We note open seams, ponding, soft insulation found underfoot and by core cuts, deck rust, and curb heights. Each section is then marked for repair, recover, or tear-off, with the order of work.
Send the address and a few roof details, or call. Every job starts with an inspection and a written scope.
